Setting up A Bathtub
Setting up A Bathtub
Blog Article
Are you trying to find selective information on How to Install a Bathtub Yourself?
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard project. If the old tub is easily obtainable, the task can move quickly; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the task is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have actually certified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is far better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually already purchased a new tub and don't need to change the setup of your previous water pipelines.
Your devices and also product list ought to make up the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, put the tub in the called for position. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub till the spirit level reads level.
To set up taps, fit all-time low of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the bath tub should wait till the bath tub has actually been made use of a minimum of when as this will settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to difficulties with moisture and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to allow for the movement experienced when the bathtub is in use. The sealer can crack rather early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that blog post was a smart idea. I beg you take a moment to promote this write-up if you enjoyed reading it. I value reading our article about How to Install a Bathtub Yourself.
This Resource
Report this page